Welcome to BigCarClub!

Site Notification:

BigCarClub is now closed to registrations. Whilst it remains available online, the site is now an archive only and will eventually expire.
Thank you to all our members who contributed over the years!

Not logged in!

Hey there, welcome to BigCarClub!
You don't need to be logged in to view the forum but the experience will be so much better if you are! Users can login or if you don't have an account already, you can create one for free by clicking the Register link in the top right corner of this page.

Advert:

Turbo to intercooler return pipe

Started by Drewby, August 23, 2013, 03:10:39 PM

Previous topic - Next topic

0 Members and 1 Guest are viewing this topic.

Print
Go Down 1
User actions
August 23, 2013, 03:10:39 PM
Can anyone help again. My driveshaft has rubbed a whole through the rubber pipe that comes from the bottom of the turbo to the metal pipe that runs back to the intercooler. I have tried retaping the hole with ductape and cable tieing the pipe out the way but no matter where I place it, it always rubs back through the pipe. On the old engine it had a metal clamp which attached to the side of the sump and held the metal pipe in place, but on this engine it doesn't have the 3 holes in the side of the sump to attach it to. So I'm running the pipe without the clamp. Also would anyone have the part no for this rubber pipe. Thanks. Andy.  Ps the pipe is just a standard 90 degree bend but 1 end is smaller than the other if that helps.
August 23, 2013, 03:54:29 PM #1
Hi Andy VW no. is 7M 3145838B

I guess your new engine is not from a galaxy, do you still have the old lump should be fairly easy to swop over the sump.
2016 Vauxhall Insignia Elite Nav in White 2.0CDTI Manual.
2023 VW Transporter T6.1 SE In Silver 2.9TDI 150PS. 7 Speed DSG Wheelchair accessible day vehicle.


With VCDS lite (full version) need a code clearing or want to scan for faults in the north kent area, PM me. All for a pint of Strongbow.
August 23, 2013, 04:02:12 PM #2
Yes still have the old engine Chris, but never swapped the sump pans over before is it difficult to do. I imagine its new gaskets etc
August 23, 2013, 04:22:18 PM #3
There is no gasket  sealer is used. Ford part no YM2J-19G204-AA
Be sure to clean off old sealer and washout sump.
Run a continuous bead of sealer on the sump going around the inner edge of the bolt holes.
2016 Vauxhall Insignia Elite Nav in White 2.0CDTI Manual.
2023 VW Transporter T6.1 SE In Silver 2.9TDI 150PS. 7 Speed DSG Wheelchair accessible day vehicle.


With VCDS lite (full version) need a code clearing or want to scan for faults in the north kent area, PM me. All for a pint of Strongbow.
August 23, 2013, 07:14:07 PM #4
Just updated this thread I started with description/pictures which may be of use.
https://www.fordmpv.com/smf2/technical/sump-refitting-degreasing-and-instant-gasket/
August 23, 2013, 11:00:49 PM #5
Thank you silverbeast some very useful information there. I'm tackling this tomorrow so wish me luck.
August 23, 2013, 11:09:48 PM #6
Good luck!

Just take it slow and steady and make sure it is thoroughly degreased before reassembly.

Forgot to say you need to leave it plenty of time to cure (I would suggest at least 24hours) I think I left it 2 days, maybe 3 as I had the luxury of being able to get a lift to/from work just to be sure.

Don't refill with oil till then and obviously check for leaks before and after you start it.
August 23, 2013, 11:23:34 PM #7
Hi Andy
With the work you have done already this should be pretty easy as the sump is very accessible on this model.
Silverbeast has recently done this job so his insructions and pictures are very helpful. :)
2016 Vauxhall Insignia Elite Nav in White 2.0CDTI Manual.
2023 VW Transporter T6.1 SE In Silver 2.9TDI 150PS. 7 Speed DSG Wheelchair accessible day vehicle.


With VCDS lite (full version) need a code clearing or want to scan for faults in the north kent area, PM me. All for a pint of Strongbow.
August 25, 2013, 05:31:20 PM #8
Jobs a good in, thanks guys but now I have another flaming problem, well I had it before but ill start another topic grrrr!!
User actions
Print
Go Up 1